search

LaserMax Stud Sensor LMS-JMX-H Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Kits de voiture LaserMax Stud Sensor LMS-JMX-H. LaserMax Stud Sensor LMS-JMX-H User's Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
To avoid unintentional battery drain,
the J-Max is set to turn off after 30
minutes of constant use. While in the
time out mode, simply cycle the
activation switch off to re-cycle the
laser, and turn it back on.
TIME OUT!
LEFT GRIP
RIGHT GRIP
LASER SIDE PLATE
GRIP SCREW
SIDE PLATE SCREWS (2)
BATTERIES (2)
LARGE HEX WRENCH (5/64)
ALIGNMENT TOOL (.035”)
LASER WARNING LABEL
BATTERY COVER
installation guide
LMS-JMX-H; LMS-JMX-NH
1.800.527.3703
e
installation guide
Installing the J-Max
Laser System
Ⓑ
Ⓒ
Ⓖ
Ⓗ
Ⓐ
Ⓔ
Ⓕ
Ⓐ
Ⓑ
Ⓒ
Ⓓ
Ⓔ
Ⓕ
Ⓖ
Ⓗ
Ⓘ
Ⓙ
What’s in the Box
a
To insert or replace batteries: Using a small flat blade screwdriver, loosen the battery
cover screw until the battery cover (J) is able to rotate. Rotate the battery cover (J)
until you are able to remove the batteries. Replace the batteries by inserting the
negative (-) end first. The batteries’ positive (+) printed side must face out. Rotate
the battery cover to its original orientation. Tighten the battery cover screw until
snug—do not over tighten. Confirm that the laser will now activate. If the laser will
not turn on—retighten the screw and try again. (See Figures f-h)
* Remove batteries when not in use for extended periods of time to preserve battery life.
Inserting the Batteries
Make sure your gun is unloaded. Double check to
verify your handgun is safe before proceeding.
Unscrew the mounting hardware on your existing
grips (in most cases this will be a single flat head
screw; refer to gun owners manual for proper size)
and remove grips. Remove the two (2) factory side
plate screws. Do not remove factory side plate or
side plate yoke screw! (See Figures a & b)
Place left side of revolver grip frame over Left Grip
(A), so that the grip frame aligns with features in Left
Grip (A). (See Figure b)
Place Laser Side Plate (C) over right side of grip
frame, aligning it with grooves and screw holes in
frame. (See Figure c)
Insert Side Plate Screws (E) into holes in Laser Side
Plate (C). Tighten with the Large Hex Wrench (G).
Do not over tighten. (See Figure d)
Position Right Grip (B) over Laser Sight Plate (C),
aligning it with grooves & screw hole.
Insert Grip Screw (D) into hole in Right Grip (B) and
through frame. Secure with flat blade screwdriver.
(See Figure e)
b
DO NOT REMOVE
screw below cylinder
Ⓙ
c d
r
e
m
o
v
e
Affix Laser Warning
Label (I) onto your
firearm as close to
the laser as possible
Ⓘ
f
Laser Side Plate (C)
g
h
Ⓓ
Vue de la page 0
1 2

Résumé du contenu

Page 1 - TIME OUT!

To avoid unintentional battery drain, the J-Max is set to turn off after 30 minutes of constant use. While in the time out mode, simply

Page 2 - LMS-JMX-H; LMS-JMX-NH

The hole at the top adjusts elevation (vertical alignment).* You can easily fine tune your laser to accommodate any weapon platform, type

Commentaires sur ces manuels

Pas de commentaire
  • Shinano Kenshi Drain It! by Planket Cencorp USAutomatic MosquitoBite Planes
  • Sharp Caisses enregistreuses Panasonic Téléphones mobiles Audio-Technica Non Diamond Multimedia Non Gigabyte Syntoniseurs de télévision par ordinateur
  • Electrolux EWT10115W Samsung SM-G925X Nikon Nikon 1 J1 Rational SelfCooking Center Samsung SGH-F500
  • Samsung CLX-9250ND Manuel de l'utilisateur Irobot Roomba 780 Manuel de l'utilisateur RCA P61939 Manuel de l'utilisateur Netgear GS105GE Fiche technique Samsung SGH-C100 Manuel de l'utilisateur